Automobile hub test bench

The automobile wheel hub test bench simulates two-wheel drive (front-wheel drive or rear-wheel drive) electric vehicle road driving conditions. It can be used for electric vehicle mileage reliability test and electric vehicle energy consumption rate test, as well as electric vehicle performance test ( Coasting test, minimum stable vehicle speed test, acceleration performance test, maximum vehicle speed test, steep slope test, etc.). It can be used in conjunction with walk-in high and low tempera

Vehicle walk-in high and low temperature humidity and heat environment test chamber

Main performance parameters： Temperature adjustment range: -40℃～+80℃ Humidity: 20～98%RH (static load) Illumination intensity range of sunshine simulation system: 300～1200W/m2 Radiation area of sunshine simulation system: length 9000mmX width 3000mm

Comprehensive test bench for automobile roll

Main performance parameters: The rollover angle of the rollover test bench is: 0°～50° Rated load capacity: 5000Kg

Rain test room

Main performance parameters: Rain position: front, back, left, right, top, bottom Rain strength: 12±1mm/min at the front, 8±1mm/min at other positions Nozzle pressure: 150±10kPa

Four-pillar road simulation fatigue test bench

By reproducing the vertical acceleration of the four wheels of the vehicle in the test field, the durability of the suspension, body and body accessories was evaluated. Main performance parameters: Passenger car with a curb weight less than 3500Kg

K&C characteristic test bench for single axle automobile suspension

The test equipment specially used to measure the K&C characteristics of the suspension adopts a quasi-static loading method to simulate the motion state of the car body when the car body rolls, pitches, or when the car turns, decelerates, and accelerates (including suspension bounce, body roll, wheel and The interaction force and moment of the ground, etc.), to measure the change characteristics of wheel alignment parameters and the stiffness characteristics of the suspension. The measured param

Power steering gear ESP test bench

The test bench is suitable for the durability test of automobile mechanical steering gear, the durability test of C-EPS belt mechanical steering gear, and the durability test of mechanical steering gear under high and low temperature conditions.

Comprehensive test bench for body static stiffness

Main performance parameters: Body-in-white torsion loading mechanism Loading force：-20000N～+20000N Loading force accuracy：0.1%FS Load range：0～200mm Body-in-white partial loading mechanism Loading force：-2500N～+2500N Loading force accuracy：0.1%FS Load range：0～50mm Body bending and sheet metal parts torsion loading mechanism Loading force：-10000N～+10000N Loading force accuracy：0.1%FS Load range：0～200mm

Braking performance simulation test bench

Braking performance simulation test bench is a special test equipment for comprehensive performance test of automobile hydraulic brake system under 3t. The entire brake system (from the actual vehicle pedal to the brake) can be arranged on the bench according to the vehicle assembly state and connected with the actual vehicle pipeline to realize the performance assessment of the vehicle brake system under the actual vehicle state; it can also be used for a single brake Braking performance test.

Motor performance test bench

Main performance parameters: Motor performance test bench (315kW) Peak power: 315kW Peak speed: 6500rpm Peak torque: 3500N.m Output voltage: 30～1000V Output current: -900～+900A The cooling method of the tested motor and controller: water cooling/air cooling

Reliability test bench

The motor reliability test bench can not only do the reliability test of the drive motor system, but also has the function of the motor performance test bench. The bench adopts dual-axis output mode, which can meet both high-speed motor test and low-speed motor test.

Electric vibration test bench

The vibration test system is mainly used to perform vibration tests on electronics, electrical products, battery modules and battery packs to test the reliability of the products. Can do sinusoidal vibration and random vibration test. It is equipped with a movable high and low temperature damp and hot environment bin, which can do vibration tests under different environmental conditions.

Rain test chamber

The rain test box can provide IPX5, IPX6 water spray test. Main performance parameters: · Working room size: 1500×1500×1500mm (D×W×H) · Turntable diameter:Φ400mm · Turntable load: about 900 kg · Sample rack speed: 1～15 r/min

Salt spray test chamber

The salt spray test chamber is suitable for corrosion resistance tests on protective layers of metal materials, electronic and electrical products. Main performance parameters: · Studio size: 1500×1500×1800 mm (D×W×H) · The amount of salt spray deposition: 1.0～2.0ml/80cm2.h · Saturator temperature: 35℃～55℃ · Salt water concentration: 5% · Air pressure: 0.15～0.2MPa

Sand and dust test chamber

Main performance parameters: Working room size: 1500×1500×1500mm (D×W×H) Metal screen: wire diameter 50um, nominal spacing between wires 75um Dust concentration: 2～4kg/m³ Air velocity: ≤2m/s

High and low temperature damp heat test chamber

The high and low temperature damp heat test chamber is suitable for electronic and electrical products to conduct high temperature, low temperature, damp and heat environmental tests according to the national standard.

MTS-ACUMEN system

Main performance parameters: Maximum test force: 1 kN Relative error of test force is less than 0.2% Deformation accuracy: 0.5%FS Stretching space: 350 mm Compressed space: 150 mm Flat sample clamping thickness 0-5 mm Maximum clamping width for flat samples: 10mm

MTS LANDMARK hydraulic servo test system

Main performance parameters: Maximum load: ±100 kN Maximum stroke: 100 mm Deformation accuracy: 0.5%FS Dynamic frequency range: 0.001Hz~D100Hz

MTS 831.50-400HZ elastomer test system

Main performance parameters: Load: 10 kN or 25 kN Load measurement accuracy: ±0.5%FS Stroke: ±20 mm Dynamic frequency range: 0.001Hz~D400Hz Function generator: sine wave, square wave, triangle wave, etc. Control method: displacement, load control

MTS 322.31 Hydraulic servo test system

Main performance parameters: Rated dynamic and static load: ±250 kN Load measurement accuracy: ±0.5%FS Rated displacement of actuator: 150 mm Displacement measurement accuracy: ±0.5%FS Operating frequency range: 0.1~8Hz Moving range of beam: not less than 300 mm Function generator: sine wave, square wave, triangle wave, etc. Control method: displacement, load control

Discovery DSC 25

Main performance parameters: Temperature range: -40℃~400℃ Temperature accuracy: ±0.1℃ Calorimetric reproducibility (indium standard metal): ±1% Baseline flatness: <100 μW Baseline reproducibility: <40 μW Linear cooling rate (with mechanical refrigeration): 10°C/min, up to -50°C; 2°C/min, up to -90°C

Discovery TGA55

Main performance parameters: Temperature range: room temperature~1000℃ Resolution: 0.1μg Scale weighing range: 1.0g Weighing accuracy: ±0.01% Heating rate: 0.1~100℃/min Cooling rate: less than 12 minutes from 1000℃ to RT Accuracy of constant temperature temperature: ±1℃

DHR rheometer

Function: DHR Rotational Rheometer is an instrument for studying and measuring the rheological properties of materials. It adopts the method of applying forced steady-state rate load, steady-state stress load, dynamic sinusoidal periodic strain load or dynamic sinusoidal periodic stress load to the sample to observe the sample pair Response data of the applied load; by measuring rheological data such as shear rate, shear stress, oscillation frequency, and stress-strain amplitude, the viscosity,